Batik In Java

INVESTIGATION shows that there never was a time when the art of batik did not flourish in Java. The robes of idols worshipped in pre-historic days were decorated very much in the same way as those of today, and apparently the modern native method of doing the work differs little from that employed so many hundreds of years ago. The literal translation from a Javanese paper on the batik art, which concludes this chapter, shows something of the confusingly elaborate process used in the East, while the description of the modern American way of working explains how comparatively simply, effective and beautiful results can be obtained.



The chief difference between the occidental and the native way of batiking is, that the occi dental starts his dyeing with the lightest colour and dyes his tones over each other, whilst the native dips his fabric in the darkest colour first and removes the wax each time that he needs a lighter shade and he only uses dyes that set by oxidation. Of course their batiks have to stand very much rougher treatment than the textiles decorated here and to make the dyes stand the terrific glare of the sun, the innumerable washings, and the regular dips taken by their wearers who are tremendously fond of bathing, it is necessary for them to take every precaution to produce fast colours. Their methods may seem complicated, but it would not be amiss if American batikers were to use a little more of the patience and craft that the native exercises, instead of eternally seeking short cuts to superficially beautiful effects.

Batiks are chiefly used in Java for wearing apparel and as a rule are made of calico which is imported from Holland and England, al-though homespun cotton is occasionally found and was used, of course, before trading with Europe developed almost "Mail Order" facilities.

JAVANESE COSTUME

The costume is similar. for men and women and consists of the "sarong," the "slendang" and the "sarong kapala." There are two types of sarong or loin-cloth worn, which are known as the "kain pandjang" and the "kain kapala"'; the former is decorated with an all-over pattern and is used for "every-day" wear, whilst the "kain kapala" is a more expensive form, which besides the all-over pattern, has at one end, from selvedge to selvedge, an elaborate design. There is no intricacy of cutting in a sarong as it consists merely of a piece of material from three to four-and-a-half yards long and about forty-two inches wide. The material used for this garment is almost always cotton of varying grades.

The Javanese sarong facing page 2 is made in four colours, the cream colour of the original material, a bright indigo blue, red, and purple which is the combination of the red and blue. The main part of the sarong is decorated with a flower and bird all-over design, the ground being the cream colour of the material, while the red dominates in the flowers and birds. The wide border has a red background with a cream floral decoration, and the narrow border has a blue background with an ornamental de-sign in cream and red. The kapale of this sarong is in red, with a scattered floral decoration and filled in with a characteristic Javanese filling-in pattern. The purple notes are scattered through the design. Facing page 4 is shown an enlarged detail of this design.

SLENDANG

The "slendang" is no more complicated as to shape and the decoration is either in the form of an all-over design, or it has a plain centre with a decorative border. It is usually about three yards long and eighteen inches wide, and it is worn by the women who throw it over their heads, scarf-wise, but its use is more general as a "carry-all" for babies and other personal effects.

HEAD-DRESS

The "sarong kapala" is a square piece of material worn chiefly by the men and is wound around the head in a kind of turban shape. After it has been folded on the head to the satisfaction of the wearer, it is taken off very care-fully and starched on the inside.

The women sometimes add an upper garment, called a "kemban"; this is just a long straight strip which is wound tightly round the body. The shoulders and arms are left bare, for they are great workers and do not allow their movements to be hampered by an undue amount of clothing.

JAVANESS DESIGN

The designing and waxing of batiks is done largely by the women whilst the men usually take care of the dyeing part of the process. The designs, whilst apparently originating with each individual worker are founded as a rule on what one might call standard designs; these have been used for generations, although in course of time they have changed in character somewhat. In most cases, any one familiar with these Javanese classics can trace the modern designs to their source and will recognize in present-day interpretations, figures well-known in native folk-lore.

Other designs have significance in that they 'designate rank or social prestige. Some hundred of these patterns have regular names, such as "batik parang rusa" and "batik swat"; these two are reserved for the exclusive use of royalty, and many designs are esteemed as much for their social ranking as for their artistic merit. Decorated silk is occasionally worn by the native aristocracy; it is not in general use, however, and is always made in the form of a " slendang" and worn as a scarf. The col-ours found in a batik can be interpreted to denote the part of Java in which it was made. Those from Djocdja and Solo are executed in rich tans, beautiful golden browns and deep indigo blue, which colours are used on the royal batiks; the work from these districts is sombre in tone but very rich in design. Pekalongan batiks are usually in white and different shades of blue, or rather cream and blue, for the native treats his fabric with oil before starting to work and this gives a rich creamy tone to the white. Dead white itself is never used as it is literally associated with the dead, being the colour of grave cloths and always signifying death. Variety of colouring in a batik will mean as a rule that the piece had its origin in the district of Samarang.

The prices of the garments of course vary according to the amount of work on the piece. "Kains" can be bought as cheaply as a dollar each and sometimes as much as $25.00 is paid; however, a batik costing as much is rare, and is usually one made to special order. About two to two-and-a-half dollars is the average price one would have to pay for a garment in Java.

TJAPS

Besides the batik done entirely by hand, the native produces a decorated material known as "tjap." This method can best be compared to block printing, the wax being printed on to the material instead of being applied with a tjanting. Instead of the wooden block associated with block printing, the native uses a sort of die made of wood, on which the design is made by the insertion, edgewise, of thin strips of brass or red copper; in some cases the whole die is made of the red copper. These "tjaps" are reminiscent of the work done in Madras where a similar process has been employed since the 15th century, for the direct application of the dyes.

Some "tjaps'' are done entirely by printing with blocks, while others are partly hand work. The dies are used as time savers when making borders or patterns with a regular repeat. The native artists consider these substitutes, which are sold to the- poorer classes for daily wear, very inferior to real batik and no Javanese of any standing would dream of " lowering himself " by wearing one.

At the present time not many die-makers are found, as there is only a comparatively small market for the work. A die is so solidly constructed and lasts so long, that once made, there is seldom a re-order of the same design. The price of dies varies according to the size and elaborateness of the design, ranging from about 25 cents, American money, to as high as $24.00. In Samarang there are still a few men who trade in these tjaps, whilst in Soerabaja there is only one man known who is able to make them.

The copper used in the making of tjaps comes in three different weights; the lightest is used for the making of fine outlines, the second weight for the heavier lines, whilst the third and heaviest weight is used for the frame work. Like the tjanting, the tjap is constructed in three parts; first, the body of the instrument which is composed of the variously bent strips of copper which make the design, then the frame-work which holds these strips together and lastly the metal handle.

The tjap has to replace the work done with the tjanting, therefore the object of the tjapmaker is to replace all tjanting lines with strips of copper of varying sizes, which, when printed, will give the effect of perfect tjanting work. To that end, the strips of copper have to be curved and bent, and are set in a vertical position, that is, with the edges uppermost; this of course is very delicate work which requires good craftsmanship and much patience.

In making the tjaps, the copper plates of different thicknesses are first cut into strips, each strip of the same width. The design for the tjap is made on paper, and the copper strips are bent in the various shapes as indicated in this design. Here is where the good craftsman-ship is essential as it is no easy matter to reproduce fine curved lines with the strips, especially in the case of flowered designs as no sharp angles may be shown in the bending of the copper. Then the whole design is soldered together, and fixed by the same process on to the frame to which the handle is attached.

This does not, however, complete the die-maker's work, for as in batik work with the tjanting where the material is waxed on both sides, so with the tjap does the fabric have to be printed on the reverse side as well. Thus, the die-maker has to make a second tjap in which the design is the exact reverse of the first one. It takes a die-maker about twenty days to make, a complete set, that is two corresponding tjaps, each about eight by eight inches square, for which he gets about $8.00. Out of this of course he has to pay for his materials.

When the tjaps are finished and found correct, that is, when every little line on one die is found to correspond exactly with the same line on the reverse block, then it is the business of the printer to print the tjaps so that no difference is shown in the design. The making of a pair of tjaps is only necessary when an irregular design is to be produced, as in the case of a symmetrical pattern the same die can be used on both sides.

For the reproduction of a not very elaborate tjanting design, a set of thirteen to fifteen tjaps is required; this means with the reverse set at least twenty-six to thirty separate dies. The original outlay for the making of a tjap may be great, but if the amount of work that can be done with one set is considered, it can be seen at once that the prices of pieces done by this process will be very low.

The printing of tjaps is practically always done by men. The workman sits on a low stool, and in front of him is a slanting table to which a large pad is attached; over this the piece that is to be printed is spread. The wax is heated in a flat pan, in which there is a pad of jute, covered with unbleached muslin. The wax is transferred to the metal by pressing the tjap on to this pad. To remove the surplus wax from the tjap the printer swings the die up and down a couple of times and then presses the tjap on to the material in the place where the decoration is desired. After covering one side of the material in this manner, the same process is repeated on the other side. As the wax shines through the fabric, it is not a difficult matter for the printer to place his die in the exact position, so that it will register correctly, but nevertheless, there will be very few pieces made in this way found without a slight inaccuracy in the design. Although all the actual line work in a tjap is done by the use of dies, a certain amount of the work, such as filling in spaces and big surfaces, has to be done by hand with the tjanting. This, however, amounts to a very small proportion of the work when compared with the amount of labour required in the making of a real batik. A good printer can print about twenty pieces of material, sarong length, a day, while it would take twelve to fifteen days to produce one piece of a similar design, with a tjanting.

The European printed imitations of batik meet with very little favour among the native Javanese, who are very critical of art and craftsmanship and the importations only find a market among the poor.

( Originally Published Early 1900's )



Batik Of Malaysia

Batiks And How To Make Them

Batik In Java

Batik - Native Industry

History Of Batik In Holland

European Use Of Batik

Batik - Utensils And Materials

Tjantings

The Batik Process

Batik - The Use Of Too Much Dye

Batik - The Value Of A Dye Record



Loading...


Home | All About Batik | Email: info@oldandsold.com